Standard Terminology Relating to Plastic Piping Systems

SCOPE
1.1 This terminology is a compilation of definitions of technical terms used in the plastic piping industry. Terms that are generally understood or adequately defined in other readily available sources are not included.  
1.2 When a term is used in an ASTM document for which Committee F17 is responsible it is included only when judged, after review, by Subcommittee F17.91 to be a generally usable term.  
1.3 Definitions that are identical to those published by other ASTM committees or other standards organizations are identified with the committee number (for example, D20) or with the abbreviation of the name of the organization (for example, IUPAC International Union of Pure and Applied Chemistry).  
1.4 A definition is a single sentence with additional information included in notes.  
1.5 Definitions are followed by the committee responsible for the standard(s) (for example, [F17.26]) and standard numbers(s) in which they are used (for example, F714).  
1.6 Abbreviated Terminology:  
1.6.1 Abbreviated terminology is intended to provide uniform contractions of terms relating to plastic piping that have evolved through widespread common usage. The compilation in this standard has been prepared to avoid the occurrence of more than one abbreviated term for a given plastics piping term and to avoid multiple meanings for abbreviated terms.  
1.6.2 The abbreviated terminology and descriptions in this standard are intended to be consistent with usage in plastics piping and the standards under F17 jurisdiction. Other ASTM Committees may assign a different word-phrase description to the same abbreviated terminology. In such cases, the abbreviated terms in this standard shall apply to usage in F17 standards, or if widespread misunderstanding could result from conflicting abbreviated terminology descriptions, the abbreviated terminology for the word-phrase shall not be used in F17 standards.  
1.6.3 Acronyms and Initialisms—A word formed from the letters or parts of words of a longer word-phrase, usually from the initial letters or parts of the words. An Acronym is pronounced as a word, for example radar, for radio detection and ranging. An Initialism is pronounced as a series of letters, for example DOT for Department of Transportation.  
1.6.4 The Acronym or Initialism description is the origin word-phrase for the Acronym or Initialism, not a definition.  
1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

General Information

Status
Historical
Publication Date
31-Dec-2018
Current Stage
Ref Project

Relations

Buy Standard

Standard
ASTM F412-19 - Standard Terminology Relating to Plastic Piping Systems
English language
20 pages
sale 15% off
Preview
sale 15% off
Preview
Standard
REDLINE ASTM F412-19 - Standard Terminology Relating to Plastic Piping Systems
English language
20 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: F412 − 19
Standard Terminology Relating to
1
Plastic Piping Systems
ThisstandardisissuedunderthefixeddesignationF412;thenumberimmediatelyfollowingthedesignationindicatestheyearoforiginal
adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.Asuperscript
epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope* 1.6.3 Acronyms and Initialisms—A word formed from the
letters or parts of words of a longer word-phrase, usually from
1.1 This terminology is a compilation of definitions of
the initial letters or parts of the words. An Acronym is
technical terms used in the plastic piping industry. Terms that
pronounced as a word, for example radar, for radio detection
are generally understood or adequately defined in other readily
and ranging. An Initialism is pronounced as a series of letters,
available sources are not included.
for example DOT for Department of Transportation.
1.2 When a term is used in an ASTM document for which
1.6.4 The Acronym or Initialism description is the origin
Committee F17 is responsible it is included only when judged,
word-phrase for the Acronym or Initialism, not a definition.
after review, by Subcommittee F17.91 to be a generally usable
1.7 This international standard was developed in accor-
term.
dance with internationally recognized principles on standard-
1.3 Definitions that are identical to those published by other
ization established in the Decision on Principles for the
ASTM committees or other standards organizations are iden-
Development of International Standards, Guides and Recom-
tified with the committee number (for example, D20) or with
mendations issued by the World Trade Organization Technical
the abbreviation of the name of the organization (for example,
Barriers to Trade (TBT) Committee.
IUPAC International Union of Pure and Applied Chemistry).
2. Referenced Documents
1.4 A definition is a single sentence with additional infor-
2
mation included in notes.
2.1 ASTM Standards:
C114 Test Methods for Chemical Analysis of Hydraulic
1.5 Definitions are followed by the committee responsible
Cement
for the standard(s) (for example, [F17.26]) and standard
D256 Test Methods for Determining the Izod Pendulum
numbers(s) in which they are used (for example, F714).
Impact Resistance of Plastics
1.6 Abbreviated Terminology:
D638 Test Method for Tensile Properties of Plastics
1.6.1 Abbreviated terminology is intended to provide uni-
D648 Test Method for Deflection Temperature of Plastics
form contractions of terms relating to plastic piping that have
Under Flexural Load in the Edgewise Position
evolved through widespread common usage. The compilation
D747 Test Method for Apparent Bending Modulus of Plas-
in this standard has been prepared to avoid the occurrence of 3
tics by Means of a Cantilever Beam (Withdrawn 2019)
morethanoneabbreviatedtermforagivenplasticspipingterm
D790 Test Methods for Flexural Properties of Unreinforced
and to avoid multiple meanings for abbreviated terms.
and Reinforced Plastics and Electrical Insulating Materi-
1.6.2 The abbreviated terminology and descriptions in this
als
standard are intended to be consistent with usage in plastics
D882 Test Method for Tensile Properties of Thin Plastic
piping and the standards under F17 jurisdiction. Other ASTM
Sheeting
Committees may assign a different word-phrase description to
D883 Terminology Relating to Plastics
the same abbreviated terminology. In such cases, the abbrevi-
D907 Terminology of Adhesives
ated terms in this standard shall apply to usage in F17
D1003 Test Method for Haze and Luminous Transmittance
standards, or if widespread misunderstanding could result from
of Transparent Plastics
conflicting abbreviated terminology descriptions, the abbrevi-
D1079 Terminology Relating to Roofing and Waterproofing
ated terminology for the word-phrase shall not be used in F17
D1238 Test Method for Melt Flow Rates of Thermoplastics
standards.
1 2
This terminology is under the jurisdiction ofASTM Committee F17 on Plastic For referenced ASTM standards, visit the ASTM website, www.astm.org, or
Piping Systems and is the direct responsibility of Subcommittee F17.91 on Editorial contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
and Terminology. Standards volume information, refer to the standard’s Document Summary page on
Current edition approved Jan. 1, 2019. Published January 2019. Originally the ASTM website.
3
approved in 1975. Last previous edition approved in 2017 as F412 – 17a. DOI: The last approved version of this historical standard is referenced on
10.1520/F0412-19. www.astm.org.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshoho
...

This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: F412 − 17a F412 − 19
Standard Terminology Relating to
1
Plastic Piping Systems
This standard is issued under the fixed designation F412; the number immediately following the designation indicates the year of original
adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A superscript
epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the U.S. Department of Defense.
1. Scope*
1.1 This terminology is a compilation of definitions of technical terms used in the plastic piping industry. Terms that are
generally understood or adequately defined in other readily available sources are not included.
1.2 When a term is used in an ASTM document for which Committee F17 is responsible it is included only when judged, after
review, by Subcommittee F17.91 to be a generally usable term.
1.3 Definitions that are identical to those published by other ASTM committees or other standards organizations are identified
with the committee number (for example, D20) or with the abbreviation of the name of the organization (for example, IUPAC
International Union of Pure and Applied Chemistry).
1.4 A definition is a single sentence with additional information included in notes.
1.5 Definitions are followed by the committee responsible for the standard(s) (for example, [F17.26]) and standard numbers(s)
in which they are used (for example, F714).
1.6 Abbreviated Terminology:
1.6.1 Abbreviated terminology is intended to provide uniform contractions of terms relating to plastic piping that have evolved
through widespread common usage. The compilation in this standard has been prepared to avoid the occurrence of more than one
abbreviated term for a given plastics piping term and to avoid multiple meanings for abbreviated terms.
1.6.2 The abbreviated terminology and descriptions in this standard are intended to be consistent with usage in plastics piping
and the standards under F17 jurisdiction. Other ASTM Committees may assign a different word-phrase description to the same
abbreviated terminology. In such cases, the abbreviated terms in this standard shall apply to usage in F17 standards, or if
widespread misunderstanding could result from conflicting abbreviated terminology descriptions, the abbreviated terminology for
the word-phrase shall not be used in F17 standards.
1.6.3 Acronyms and Initialisms—A word formed from the letters or parts of words of a longer word-phrase, usually from the
initial letters or parts of the words. An Acronym is pronounced as a word, for example radar, for radio detection and ranging. An
Initialism is pronounced as a series of letters, for example DOT for Department of Transportation.
1.6.4 The Acronym or Initialism description is the origin word-phrase for the Acronym or Initialism, not a definition.
1.7 This international standard was developed in accordance with internationally recognized principles on standardization
established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued
by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents
2
2.1 ASTM Standards:
C114 Test Methods for Chemical Analysis of Hydraulic Cement
D256 Test Methods for Determining the Izod Pendulum Impact Resistance of Plastics
D638 Test Method for Tensile Properties of Plastics
D648 Test Method for Deflection Temperature of Plastics Under Flexural Load in the Edgewise Position
1
This terminology is under the jurisdiction of ASTM Committee F17 on Plastic Piping Systems and is the direct responsibility of Subcommittee F17.91 on Editorial and
Terminology.
Current edition approved Aug. 1, 2017Jan. 1, 2019. Published August 2017January 2019. Originally approved in 1975. Last previous edition approved in 2017 as
F412 – 17.F412 – 17a. DOI: 10.1520/F0412-17A.10.1520/F0412-19.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
F412 − 19
3
D747 Test Method for Apparent Bending Modulus of Plastics by Means of a Cantilever B
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.